aluminum electrolytic capacitors voltage capacitance 105c marking lot no. a2p 10 16v plastic platform 0.3max. 5.8 0.3 d 0.5 b 0.2 c 0.2 0.5max. a 0.2 a 0.2 e positive negative a b c e 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 0.5 to 0.8 (mm) d voltage mark for 6.3v is 6v . u 1 u 2 t 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration taping code capacitance tolerance ( 20%) rated voltage (16v) rated capacitance (10f) series name type ut series 6mml chip type , wide temperature range chip type with load life 2000 hours at +105 ? . designed for surface mounting on high density pc board. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2011/65/eu). chip type specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life resistance to soldering heat marking performance characteristics item 55 to +105? 4 to 50v 0.1 to 100 f 20% at 120hz, 20? after 2 minutes' application of rated voltage, leakage current is not more than 0.01 cv or 3 ( a) , whichever is greater. black print on the case top. measurement frequency :120hz at 20? the specifications listed at right shall be met when the capacitors are restored to 20 ? after the rated voltage is applied for 2000 hours at 105?. after storing the capacitors under no load at 105? for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20?, they shall meet the specified values for the endurance characteristics listed above. type numbering system (example : 16v 10 f) dimensions rated ripple current (marms) at 105? 120hz rated voltage (v) tan (max.) 4 0.37 50 0.12 35 0.13 25 0.16 16 0.20 10 0.24 6.3 0.28 measurement frequency :120hz z 25? / z+20? z 40? / z+20? rated voltage (v) impedance ratio zt / z20 (max.) 4 6 12 6.3 3 8 10 3 5 16 2 4 25 2 3 35 2 3 50 2 3 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 4 5 5 6.3 22 30 36 60 0g 4 0j 6.3 1a 10 1c 16 1e 25 1v 35 1h 50 4 5 5 6.3 22 30 36 60 5 5 6.3 6.3 27 35 46 60 4 5 6.3 6.3 18 30 40 50 4 5 6.3 6.3 13 23 38 48 4 5 6.3 15 25 42 4 4 4 4 4 4 4 5 6.3 1.0 2.6 3.2 3.8 6.2 11 14 19 30 allowable ripple cap.( f) v code the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250?. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20?. tan capacitance change 200% or less than the initial specified value leakage current less than or equal to the initial specified value within 25% of the initial capacitance value (16v or less) within 20% of the initial capacitance value (25v or more) capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value rated ripple frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.70 1.00 1.17 1.36 1.50 case size d (mm) ut ua long life wt higher c/ v long life ux taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please select ux(p.158), uj(p.164) series if high c/v products are required. please refer to page 3 for the minimum order quantity. cat.8100c
|
